for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 1 filters - tunable - smt 3 HMC1000LP5E v00.0311 functional diagram the HMC1000LP5E is a mmic band reject flter which features a user selectable band rejection frequency. the -20 db flter bandwidth is < 10%. the rejection frequency can be varied between 3.6 and 12.2 ghz by applying an analog tune voltage between 0 and 14v. this tunable flter can be used as a much smaller smt alternative to physically large switched flter banks and cavity tuned flters. the HMC1000LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications. typical applications features general description filter - tunable, band reject smt 3.6-12.2 ghz the HMC1000LP5E is ideal for: ? test & measurement equipment ? military radar & ew/ecm ? satcom & space ? industrial & medical equipment tunable stopband frequency: 3.6-12.2 ghz tunable stopband rejection: 25 db typical four frequency control modes single chip replacement for mechanically tuned designs 32 lead 5 x 5 mm smt package electrical specifcations, t a = +25 c parameter min. typ. max. units rejection band tuning range 3.6 12.2 ghz passband frequency range 0.1-25 ghz stopband rejection 25 db passband insertion loss 3 db return loss (passband and rejection band) 15 db rejection band input ip3 (pin = + 10 dbm) 23.5 dbm passband input ip3 (pin = + 10 dbm) 35 dbm input power @ 5 shift in insertion phase (vt1 = vt2 = 0v) 10 dbm input power @ 5 shift in insertion phase (vt1 = vt2 = 7v) 13 dbm input power @ 5 shift in insertion phase (vt1 = vt2 = 14v) >18 dbm frequency control voltage (v fctl ) 0 14 v source/sink current (i fctl ) 1 ma residual phase noise [1] (100 khz offset) -162 dbc/hz rejection band, f center drift rate -0.3 mhz/c tuning speed, phase settling to within 10 [2] < 200 ns [1] optimum residual phase noise performance requires the use of a low noise driver circuit. [2] tuning speed includes 40 ns typical tuning voltage ramp from driver.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 2 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz broadband insertion loss vs. vt broadband return loss (s22) vs. vt rejection vs. temperature broadband return loss (s11) vs. vt rejection band, fcenter vs. temperature rejection bandwidth vs. vt1 = vt2 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 insertion loss (db) frequency (ghz) 0v 14v 8v 4v -40 -30 -20 -10 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s11 0v s11 7v s11 14v return loss (db) frequency (ghz) -40 -30 -20 -10 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s22 0v s22 7v s22 14v return loss (db) frequency (ghz) 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 +25c +85c -40c rejection band, fcenter (ghz) vt1 = vt2 (vdc) 20 25 30 35 40 45 50 0 2 4 6 8 10 12 14 +25c +85c -40c rejection (db) vt1 = vt2 (vdc) 0 5 10 15 20 25 30 35 40 45 50 0 2 4 6 8 10 12 14 - 10 db bw - 20 db bw bandwidth (%) vt1 = vt2 (vdc) tuning mode 1, full band frequency tuning, (vt1 = vt2 = 0-14v)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 3 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz broadband insertion loss vs. vt broadband return loss (s11) vs. vt rejection band, fcenter vs. temperature rejection vs. temperature rejection bandwidth vs. vt1 broadband return loss (s22) vs. vt -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 insertion loss (db) frequency (ghz) 0v 14v 8v 4v -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s11 0v s11 7v s11 14v return loss (db) frequency (ghz) -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s22 0v s22 7v s22 14v return loss (db) frequency (ghz) 2 3 4 5 6 7 8 0 2 4 6 8 10 12 14 +25c +85c -40c rejection band, fcenter (ghz) vt1 (vdc) 20 25 30 35 40 45 50 0 2 4 6 8 10 12 14 +25c +85c -40c rejection (db) vt1 (vdc) 0 5 10 15 20 25 30 35 40 0 2 4 6 8 10 12 14 - 10 db bw - 20 db bw bandwidth (%) vt1 (vdc) tuning mode 2, low band tuning with narrower rejection bandwidth (vt1 = 0-14v, vt2 = 0v)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 4 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz broadband insertion loss vs. vt broadband return loss (s22) vs. vt rejection band, fcenter vs. temperature rejection bandwidth vs. vt2 broadband return loss (s11) vs. vt rejection vs. temperature -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 insertion loss (db) frequency (ghz) 0v 14v 8v 4v -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s11 0v s11 7v s11 14v return loss (db) frequency (ghz) -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s22 0v s22 7v s22 14v return loss (db) frequency (ghz) 6 7 8 9 10 11 12 13 14 0 2 4 6 8 10 12 14 +25c +85c -40c rejection band, fcenter (ghz) vt2 (vdc) 15 20 25 30 35 0 2 4 6 8 10 12 14 +25c +85c -40c rejection (db) vt2 (vdc) 0 5 10 15 20 25 30 35 40 0 2 4 6 8 10 12 14 - 10 db bw - 20 db bw bandwidth (%) vt2 (vdc) tuning mode 3, high band tuning with narrower rejection bandwidth (vt1 = 14v, vt2 = 0-14v)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 5 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz tuning mode 4, rejection bandwidth tuning (vt1 = 0v, vt2 = 0-14v) broadband insertion loss vs. vt broadband return loss (s11) vs. vt broadband return loss (s22) vs. vt rejection bandwidth vs. temperature insertion loss = - 10 db rejection vs. temperature, vt2 = 14v tuning sensitivity vs. vt -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 insertion loss (db) frequency (ghz) 0v 14v 8v 4v -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s11 0v s11 7v s11 14v return loss (db) frequency (ghz) -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 s22 0v s22 7v s22 14v return loss (db) frequency (ghz) 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 +25c +85c -40c bandwidth (ghz) vt2 (vdc) -35 -30 -25 -20 -15 -10 -5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 +25c +85c -40c insertion loss (db) frequency (ghz) 0 200 400 600 800 1000 1200 1400 1600 1 2 3 4 5 6 7 8 9 10 11 12 13 14 mode 1 mode 2 mode 3 mode 4 sensitivity (mhz/volt) vt (vdc)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 6 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz rejection band, input ip3, pin = +10 dbm passband, input ip3 pin = +10 dbm passband, residual phase noise @ 4 ghz, vt1 = vt2 = 14v 10 15 20 25 30 35 40 45 50 0 2 4 6 8 10 12 14 +25c +85c -40c input ip3 (dbm) vt1 = vt2 (vdc) 20 25 30 35 40 45 50 55 0 2 4 6 8 10 12 14 2 ghz 18 ghz 24 ghz input ip3 (dbm) vt1 = vt2 (vdc) passband, residual phase noise @ 17 ghz, vt1 = vt2 = 0v -180 -170 -160 -150 -140 -130 -120 1e+2 1e+3 1e+4 1e+5 1e+6 1e+7 +25c +85c -40c residual phase noise (dbc/hz) offset frequency (hz) -180 -170 -160 -150 -140 -130 -120 1e+2 1e+3 1e+4 1e+5 1e+6 1e+7 +25c +85c -40c residual phase noise (dbc/hz) offset frequency (hz) rejection band, insertion phase vs. pin rejection band, fcenter vs. pin -25 -20 -15 -10 -5 0 5 10 15 20 25 0 2 4 6 8 10 12 14 16 18 vt1=vt2=0v vt1=vt2=7v vt1=vt2=10v vt1=vt2=14v insertion phase (degrees) input power (dbm) -80 -60 -40 -20 0 20 40 60 80 0 2 4 6 8 10 12 14 16 18 vt1=vt2=0v vt1=vt2=7v vt1=vt2=10v vt1=vt2=14v frequency (mhz) input power (dbm)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 7 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz electrostatic sensitive device observe handling precautions absolute maximum ratings four operation modes and the control conditions reliability information frequency control voltage (vfctl) -0.5 to +15v rf power input 28.5 dbm storage temperature -65 to +150 c esd sensitivity (hbm) class 1 a mode vt1 vt2 description i 0 -14v vt1 = vt2 0 -14v vt1 = vt2 full band frequency tuning ii 0 - 14v 0 v low band frequency tuning, with narrower rejection bandwidth iii 14v 0 - 14v high band frequency tuning, with narrower rejection bandwidth iv 0 v 0 - 14v rejection bandwidth tuning junction temperature to maintain 1 million hour mttf 150 c nominal junction temperature (t = 85 c and pin = 10 dbm) 86 c thermal resistance (junction to ground paddle) 40 c/w operating temperature -40 to +85 c
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 8 filters - tunable - smt 3 outline drawing notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. lead spacing tolerance is non-cumulative. 4. pin burr length shall be 0.15 mm maximum. pin burr height shall be 0.05 mm maximum. 5. package warp shall not exceed 0.05 mm. 6. all ground leads and ground paddle must be soldered to pcb rf ground. 7. refer to hittite application note for suggested land pattern. part number package body material lead finish msl rating package marking [1] HMC1000LP5E rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] h1000 xxxx [1] 4-digit lot number xxxx [2] max peak refow temperature of 260 c package information HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 9 filters - tunable - smt 3 HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz pin descriptions application circuit pin number function description interface schematic 1-4, 7-11, 13, 15-18, 21-25, 27-32 n/c the pins are not connected internally; however, all data shown herein was measured with these pins connected to rf/dc ground externally. 5, 20, 26 gnd these pins and exposed paddle must be connected to rf/dc ground. 6 rfin this pin is ac coupled and matched to 50 ohms. 12, 14 vt1, vt2 center frequency control voltage. 19 rfout this pin is ac coupled and matched to 50 ohms.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com 3 - 10 filters - tunable - smt 3 evaluation pcb the circuit board used in the application should use rf circuit design techniques. signal lines should have 50 ohms impedance while the package ground leads and exposed paddle should be con - nected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from hittite upon request. list of materials for evaluation pcb eval01-HMC1000LP5E [1] item description j1, j2 connector, 2.9 mm, jack j3, j4, j5 dc pin u1 HMC1000LP5E, band reject filter- tunable pcb [2] 600-00121-00 evaluation pcb [1] reference this number when ordering complete evaluation pcb [2] circuit board material: arlon 25fr or rogers 25fr HMC1000LP5E v00.0311 filter - tunable, band reject smt 3.6-12.2 ghz
|
